The board foot formula
A board foot is a unit of wood volume: a piece 1 inch thick, 12 inches wide and 12 inches long, which is 144 cubic inches. The Virginia Department of Forestry uses exactly that definition. It lets a lumberyard price boards of any size by the same yardstick.
To calculate board feet, multiply thickness in inches by width in inches by length in feet, then divide by 12. If you measured the length in inches too, divide by 144 instead. Multiply by the number of identical pieces for the total.
Pricing hardwood by the board foot
Hardwood dealers usually quote a price per board foot, because their boards come in varied widths and lengths. The Wood Handbook from the USDA Forest Products Laboratory notes that hardwood lumber is usually manufactured to random widths and that standard lengths run in 1-foot steps from 4 to 16 feet.
That means you price each board as you pick it. Measure the width at a representative point, multiply out, and add the boards together. The Board Foot Calculator takes a price per board foot and returns the cost directly.
Quarters, nominal sizes and which thickness to use
Hardwood thickness is often written in quarters of an inch: 4/4 is 1 inch, 5/4 is 1¼ inches, 8/4 is 2 inches. These describe rough-sawn thickness. The Wood Handbook’s table of standard hardwood sizes shows rough 1-inch stock surfacing to 13/16 inch, so a "4/4" board you buy planed may measure well under an inch.
Softwood construction lumber goes by nominal sizes. NIST explains that a two-by-four actually measures 1.5 by 3.5 inches, and the Wood Handbook lists a dry 2 × 8 at 1½ by 7¼ inches. Nominal sizes come from the rough dimensions before the boards were surfaced at the mill.
The rule for your calculation is simple: use the dimensions the seller bills on. That is usually the nominal or rough size, not the size you measure with calipers. Using actual dimensions on a 2 × 4 × 8 gives 3.5 board feet instead of the 5.3333 a yard would tally, and your price comparisons will not line up.
Budgeting a project with waste and delivery
Your cut list tells you how much finished wood the project needs, but you will lose some to defects, knots, end checks and saw kerfs. Add a waste allowance before you shop. Rough lumber with defects needs a bigger allowance than clear, surfaced stock.
Say a bookcase needs six boards of 4/4 stock, each 6 inches wide and 8 feet long. That is 24 board feet. At $8.50 per board foot, the Board Foot Calculator prices the wood at $204.00. Feeding the same 24 board feet into the Material Cost Calculator with a 25% waste allowance and $40 delivery gives $295.00.
The 25% here is a planning assumption, not a standard. Choose your own figure based on the grade you are buying and how much of each board your cut list can use.
Board feet, cubic feet and linear feet
A cubic foot is 12 × 12 × 12 = 1,728 cubic inches, and a board foot is 144. So one cubic foot holds 12 board feet. Divide board feet by 12 to get nominal cubic feet, which is useful for estimating weight or comparing with firewood or log measurements.
Linear feet only measure length. Trim, molding and many softwood boards at home centers are priced per linear foot or per piece. To compare that price with a board-foot price, find the board feet in one linear foot of the profile: thickness × width ÷ 12. A 1 × 6 has 0.5 board foot per linear foot, so $3.00 per linear foot equals $6.00 per board foot.
Edge cases: big timbers and thin stock
Board feet climb quickly with thickness, because thickness and width multiply. A single 6 × 6 post 12 feet long holds 36 board feet, as much as nine 1 × 4 boards of the same length. If a timber framer or sawmill quotes per board foot, run the numbers before assuming a few posts are cheap.
At the other end, stock thinner than an inch still counts in proportion. A 1/2-inch board 6 inches wide and 8 feet long is 2 board feet, half of what the same board would be at a full inch. Enter the fraction as a decimal, 0.5, in the thickness field.
Common mistakes
Dividing by the wrong number. Divide by 12 when the length is in feet and by 144 when every dimension is in inches. Mixing the two makes the answer 12 times too big or too small.
Rounding thickness down to actual size. As above, this undercounts what the yard will charge and makes your budget look cheaper than it is.
Forgetting the quantity. The formula gives board feet per piece. Multiply by the number of pieces before pricing.
Measuring width at the narrowest point on a tapered or wany board. Ask how your supplier tallies boards like these before you total up a pile, so your count matches the invoice.
Which calculator to use
Use the Board Foot Calculator for any stack of identical pieces. Enter thickness and width in inches, length in feet, the number of pieces and, if you know it, the price per board foot. Run it once per board size and add the totals.
Use the Material Cost Calculator once you have the total board feet and want a budget figure that includes a waste allowance and a delivery charge. It works with any unit, so you can also use it for sheet goods priced per sheet or hardware priced per box.
Sources and further reading
- Virginia Department of Forestry: Board foot (glossary)
- USDA Forest Products Laboratory: Wood Handbook (FPL-GTR-282), Chapter 6, Commercial Lumber, Round Timbers, and Ties
- NIST: Making Sure Lumber Measures Up