1. Home
  2. Construction
  3. Board Foot Calculator
Construction

Board Foot Calculator

Convert lumber dimensions and piece count to board feet and an estimated cost.

Your numbers

in
in
ft

Results update as you type. Nothing you enter is sent anywhere.

Result

120 board feet · $132.00

2 in × 6 in × 10 ft ÷ 12 = 10 board feet per piece × 12. One board foot is 144 cubic inches (12 in × 12 in × 1 in). Softwood is usually tallied on nominal sizes (a 2×4 is billed as 2 × 4 even though it measures about 1½ × 3½ in). Cost at $1.10 per board foot.

Formula used

Board feet = thickness (in) × width (in) × length (ft) ÷ 12 × pieces

A board foot is the volume unit lumberyards use to price hardwood and many softwood orders: a piece 12 inches wide, 12 inches long and 1 inch thick. This calculator converts thickness, width, length and piece count into board feet, and multiplies by a price per board foot if you have a quote.

How to use the Board Foot calculator

  1. Enter the Thickness and Width in inches. For softwood dimension lumber use the nominal size (2 and 4 for a 2×4); for rough hardwood use the quarter thickness (4/4 = 1, 8/4 = 2).
  2. Enter the Length in feet, for example 8 for an 8-foot board.
  3. Enter the Number of pieces of that size.
  4. Enter the Price per board foot from your supplier, or 0 to see volume only.
  5. Run each size separately and add the totals when your order mixes sizes.

How the board foot calculation works

FormulaBoard feet = thickness (in) × width (in) × length (ft) ÷ 12 × pieces

Nominal versus actual lumber sizes

A 2×4 does not measure 2 by 4 inches. NIST, which publishes the American Softwood Lumber Standard, explains that nominal sizes come from the rough lumber before it is surfaced at the mill, so a dry 2×4 ends up about 1½ by 3½ inches. A 2×6 is about 1½ by 5½, and a 1×6 about ¾ by 5½.

Board footage is normally tallied on the nominal numbers. The USDA Forest Products Laboratory's Wood Handbook describes the board foot as nominal thickness times nominal width times actual length, with lumber under 1 inch nominal counted as 1 inch thick. If you enter the measured 1½ × 3½ size instead, you will get a smaller figure than the yard bills, so match the sizes on your quote.

Hardwood quarters and planning waste

Hardwood is sold rough by thickness in quarter inches: 4/4 is 1 inch, 5/4 is 1¼, 6/4 is 1½ and 8/4 is 2. Widths and lengths vary board to board, so a yard measures each one and adds them up. For random-width stock, enter the average width or run each board separately.

The result is the volume you buy, not the volume you keep. Planing, ripping and cutting around knots remove material, so woodworkers commonly order extra; the right allowance depends on the species, grade and project. This calculator does not add waste for you.

Worked example

Five 4/4 boards, 8 inches wide and 6 feet long

Thickness: 1 in · Width: 8 in · Length: 6 ft · Number of pieces: 5 · Price per board foot (0 to skip): 6.50

  1. Board feet per piece = 1 × 8 × 6 ÷ 12 = 4.
  2. Five pieces = 4 × 5 = 20 board feet.
  3. Cost = 20 × 6.50 = 130.

Result: 20 board feet · $130.00

Assumptions and limits

Enter the dimensions your supplier bills on: nominal sizes for softwood dimension lumber, rough thickness (for example 4/4 = 1 in) for hardwood. No waste allowance.

Formula and worked examples last checked November 20, 2026. Spotted a problem? Report an error.

Frequently asked questions

How many board feet are in a 2×4×8?

Using nominal sizes, 2 × 4 × 8 ÷ 12 = 5.33 board feet. Ten of them make 53.33 board feet. Retail stores usually price 2×4s by the piece, but the board-foot figure helps compare prices across sizes.

What is the formula for board feet?

Multiply thickness in inches by width in inches by length in feet and divide by 12. If all three are in inches, divide by 144 instead, since one board foot is 144 cubic inches.

How do I convert board feet to cubic feet?

Divide board feet by 12, because one board foot is one-twelfth of a cubic foot. So 120 board feet is a nominal 10 cubic feet; the actual wood volume is smaller after surfacing.

Should I use rough or surfaced dimensions?

Use the dimensions your supplier bills on. Hardwood dealers usually tally rough thickness even when they surface the boards for you, and softwood is tallied on nominal sizes. Ask the yard if the quote does not say.

Sources