1. Home
  2. Science & engineering
  3. Ohm's Law Calculator
Science & engineering

Ohm's Law Calculator

Solve voltage, current or resistance for an ideal ohmic component.

Your numbers

A
ohm

Results update as you type. Nothing you enter is sent anywhere.

Result

10 V

V = I × R; I = V/R; R = V/I. SI units; idealized classical equation. Not a safety assessment or certified engineering design. Enter only the two known quantities. DC/resistive magnitudes only.

Formula used

V = I × R; I = V/R; R = V/I

Ohm's law links three quantities in a resistive circuit: voltage, current and resistance. Pick the one you don't know, enter the other two, and the calculator returns the missing value in volts, amperes or ohms. It suits sizing a resistor, checking a measured reading, or estimating the current a heating element draws.

How to use the Ohm's Law calculator

  1. Use the Solve for menu to choose voltage, current or resistance. The field for that quantity disappears.
  2. Type the two remaining values in base units: Voltage in V, Current in A, Resistance in ohm.
  3. Convert prefixes before typing: 20 mA is 0.02 A, 4.7 kΩ is 4700 ohm, and 500 mV is 0.5 V.
  4. Read the answer with its unit. Very small results switch to scientific notation, for example 2.5 × 10⁻⁷ A.

How the ohm's law calculation works

FormulaV = I × R; I = V/R; R = V/I

The three forms and what the code checks

The tool uses V = I × R when you solve for voltage, I = V ÷ R for current and R = V ÷ I for resistance. Values you leave in a hidden field are ignored, so switching the Solve for menu never mixes in a stale number.

All three inputs must be zero or positive. Dividing by zero is blocked: a resistance of 0 is rejected when you solve for current, and a current of 0 is rejected when you solve for resistance. Results are shown to at most six decimal places, which is enough for milliamp and microamp work.

When Ohm's law does not describe your part

A material is called ohmic when the ratio of voltage to current stays constant across a wide range of voltages. Plain resistors and heater wire behave this way over their working range. LEDs, diodes and transistors do not, so you cannot read an LED's "resistance" off its datasheet voltage and current and expect it to hold at other voltages.

For LEDs, use Ohm's law on the series resistor instead: subtract the LED's forward voltage from the supply and solve for resistance using the target current. The second example below does exactly that.

In AC circuits with motors, transformers or capacitors, the opposition to current is impedance, which includes a phase angle. This calculator treats every value as a DC or purely resistive magnitude.

Worked examples

Current through a 470 ohm resistor on a 9 V battery

Solve for: current · Voltage: 9 V · Resistance: 470 ohm

  1. I = V ÷ R
  2. I = 9 ÷ 470
  3. I = 0.0191489… A, about 19.1 mA
  4. The calculator rounds to six decimal places.

Result: 0.019149 A

Series resistor for an LED

Solve for: resistance · Voltage: 3 V · Current: 0.02 A

  1. A 5 V supply drives an LED with a 2 V forward voltage, so the resistor drops 5 − 2 = 3 V.
  2. Target current is 20 mA = 0.02 A.
  3. R = V ÷ I = 3 ÷ 0.02 = 150 ohm

Result: 150 ohm

Assumptions and limits

SI units; idealized classical equation. Not a safety assessment or certified engineering design. Enter only the two known quantities. DC/resistive magnitudes only.

Formula and worked examples last checked November 20, 2026. Spotted a problem? Report an error.

Frequently asked questions

What is the formula triangle for Ohm's law?

Write V at the top and I and R side by side underneath. Cover the quantity you want: covering V leaves I × R, covering I leaves V over R, and covering R leaves V over I. The Solve for menu performs the same three rearrangements.

How do I enter milliamps or kilohms?

Convert to base units first. Divide milliamps by 1,000 (250 mA = 0.25 A) and multiply kilohms by 1,000 (2.2 kΩ = 2200 ohm). Entering 250 in the Current field would mean 250 amperes and give an answer 1,000 times too large or small.

Can Ohm's law tell me the power a resistor must handle?

Not directly, but it gives you the numbers you need. Once you know voltage and current, power is V × I, which is the same as I² × R or V² ÷ R. Run the Electrical Power Calculator with your two values, then pick a resistor rated comfortably above that figure.

Why does my multimeter reading differ from the calculated value?

Real resistors have a tolerance band, so a 470 ohm part can measure several ohms either way. Batteries also sag below their label voltage under load, and meter leads add a little resistance on low-ohm readings. Use measured values in the calculator when you need a close match.

Does Ohm's law work for household AC outlets?

It works for purely resistive loads such as a toaster element, using RMS voltage and current. For loads with motors or electronic power supplies, current and voltage are out of phase, and you need impedance and power factor, which this tool does not model.

Sources