1. Home
  2. Construction
  3. Tile Calculator
Construction

Tile Calculator

Estimate the number of whole tiles for a net area.

Your numbers

m²
m
m
%

Results update as you type. Nothing you enter is sent anywhere.

Result

44 tiles

Tiles = ceiling(area ÷ (tile length × tile width) × (1 + waste/100)). Rounds up to whole tiles. Grout gaps and pattern layout are not modeled; verify with an installer.

Formula used

Tiles = ceiling(area ÷ (tile length × tile width) × (1 + waste/100))

The Tile Calculator works out how many whole tiles you need to cover a floor or wall, including extra for cuts and breakage. Enter the area and the tile size and it rounds up to a full tile count, which you can then turn into boxes.

How to use the Tile calculator

  1. Enter Net tiled area in square meters. For walls, subtract windows, doors and anything not being tiled.
  2. Enter Tile length and Tile width in meters. A 30 × 30 cm tile is 0.3 × 0.3; a 12 × 24 inch tile is 0.3048 × 0.6096.
  3. Set Waste allowance for cuts, breakage and spares.
  4. Read the tile count and divide by the tiles per box, rounding up.

How the tile calculation works

FormulaTiles = ceiling(area ÷ (tile length × tile width) × (1 + waste/100))

Choosing a waste allowance

Every cut at a wall edge or around a pipe creates offcuts that often cannot be reused. Small rooms with many edges, diagonal layouts and herringbone patterns produce more waste than a large open floor laid straight. Large-format tiles waste more per cut, because a single offcut is a big piece.

Keep a few spare tiles after the job. If one cracks years later, the same color and batch may no longer be sold, and a spare saves replacing the whole floor.

What the count leaves out

The calculator divides area by the face size of one tile and does not add grout joint width, so it slightly overstates the count for tiles with wide joints. It also does not plan the layout: where the cuts fall, centering in a room, or matching patterns. Those decisions can change how many tiles you need, so an installer's layout check is worthwhile on expensive tile.

Tiles are rounded up to whole units. Boxes are not, because box sizes vary by product; the box label lists the tile count or the area covered.

Worked example

A 4.5 m² bathroom floor with 30 × 30 cm tiles and 10% waste

Net tiled area: 4.5 m² · Tile length: 0.3 m · Tile width: 0.3 m · Waste allowance: 10 %

  1. One tile covers 0.3 × 0.3 = 0.09 m².
  2. Tiles without waste: 4.5 ÷ 0.09 = 50.
  3. With 10% extra: 50 × 1.10 = 55, already a whole number.
  4. If a box holds 11 tiles, you need 55 ÷ 11 = 5 boxes.

Result: 55 tiles

Assumptions and limits

Rounds up to whole tiles. Grout gaps and pattern layout are not modeled; verify with an installer.

Formula and worked examples last checked November 20, 2026. Spotted a problem? Report an error.

Frequently asked questions

How many tiles do I need for 100 square feet?

Convert to square meters (100 × 0.0929 = 9.29 m²) or divide 100 by the tile's area in square feet. A 12 × 12 in tile covers 1 ft², so 100 tiles before waste, or 110 with 10% extra.

How much extra tile should I buy?

That depends on the room shape, layout and tile size. Simple rooms laid straight need the least; diagonal or herringbone layouts and rooms with many corners need more. Ask your installer or tile supplier for a figure for your pattern.

Does grout spacing change how many tiles I need?

Slightly. Joints take up a little of the area, so the real count is a bit lower than this calculator's figure, which ignores joint width. With small tiles and wide joints the difference grows, but the extra acts as part of your waste allowance.

How do I enter tile sizes in inches?

Multiply inches by 0.0254. A 12 × 24 in tile is 0.3048 × 0.6096 m, and a 6 × 6 in tile is 0.1524 × 0.1524 m.

Sources